steine01 so once i identify the IP address, is there any need for me to change the IP address back to its original address (192.168.0.75)? If there is, do I follow the steps as shown in the ARTIQ manual?
or is the first step once i've identified the IP address is to change the IP address in device_db.py to the current IP address?
Whether you can work with the IP address on the device heavily depends on your surrounding network. For example, if you work at an institution that requires certain static IP addresses to connect devices to the lab network, you need to change the IP address in accordance with this requirement. But you may be able to use the IP address as is just as well and just need to change it in the device_db.py file.
A good first check is to just ´ping´ the IP address of ARTIQ from the PC you want to use to control the system. If you get a response, everything is ok, otherwise there is some other problem.
Changing the IP address works as shown in the manual, yes.
steine01 Hi again, I just installed OpenOCD because I needed it to continue the artiq_flash start reset of the crate, yet when I did it I have a message that says that no device was found.
I have the Kasli connected to the PC using an Ethernet cable, and have installed the Hterm.
Also, do I need a config file loaded into Hterm before I attempt to restart the Kasli
Edit: When you mentioned the power connector, did you mean the physical plug to the Kasli?
I have the Kasli connected to the PC using an Ethernet cable, and have installed the Hterm.
You need to connect the Kasli via a USB connection to your PC to access the serial interface via hterm or artiq_flash. The USB port ist just below your power supply cable.
Also, do I need a config file loaded into Hterm before I attempt to restart the Kasli
No what you need to do though, is choose the correct port once the Kasli is connected. When you connect it, more options should appear in the list and one of them should print a message once the Kasli starts up.
When you mentioned the power connector, did you mean the physical plug to the Kasli?
Yes that is what I meant.
Hmm that is weird. I had a similiar issue once and it had something to do with having to replace USB drivers on Windows. But since it looks like you use a Unix system, this should not affect you. I suggest you contact M-Labs directly via the helpdesk (helpdesk@m-labs.hk) and talk to them about the IP address and the serial connection issue, since you bought the system directly from them.
Ok I do not know why there was an error with the other serial connections or what you did to fix it, but this looks like the ouput from the Kasli on boot. And your IP address is 192.169.0.75.
This here is a screenshot from the terminal after I attempted to ping the IP address 192.169.0.75 but this is the output I got.
Now, usually, when you ping the correct IP address, I should get a response, but here that doesn't seem to be the case. My guess is that my local network is configured to be 192.168.0.75. If this isn't the response that I should not be expecting, do let me know.
Also, I attempted to change the IP address from a suggestion by Helpdesk, using the following commands
artiq_mkfs flash_storage.img -s ip 192.168.0.75
artiq_flash -f flash_storage.img storage start
as referenced from the ARTIQ manual
The first line seemed to work, but when I inputted the next line, this is my output
saying that I am missing proxy bitstream bscan_spi_xc7a100t.bit
In another attempt, I tried the next line of code
as referenced from the ARTIQ manual
but the output I got is a TimeoutError
This here is a screenshot from the terminal after I attempted to ping the IP address 192.169.0.75 but this is the output I got.
This seems very wrong. I don't see why you need super user access for ping, it should work from a normal user unless I am missing something. Also you do not get any response at all, usually there is a timeout of some sort. As long as you cannot ping the device I think you have to investigate this issue. Can you ping other devices from this PC? What are their IP addresses?
In another attempt, I tried the next line of code
This will only work if you already have network access, since it uses the ethernet connection for artiq_coremgmt commands.
The first line seemed to work, but when I inputted the next line, this is my output
This sounds like a) you have not connected the PC run this command to the Kasli via USB or b) you did not install openocd as required by the manual.
@steine01 I am attempting another method where I make direct connection with the PC and the Kasli board
I am not entirely sure what to do here: do I enter the IP address of the Kasli board under "Routes" and fill it in in both the Address and Gateway section?
My plan is to make a direct connection with two devices manually.
Okliam I am not entirely sure what to do here: do I enter the IP address of the Kasli board under "Routes" and fill it in in both the Address and Gateway section?
No. You don't need a gateway if it's the same network, and also Linux normally adds by default a route to networks for which you set IP/netmask, so you probably can leave that "Routes" section blank (I'm more familiar with the command line configuration than this GUI though).
