Asking for help

D
AD9910: Mirror frequencies invert sign of phase accumulation
- Asking for helpARTIQSinara
- Background When the AD9910's digital ramp generator (DRG) starts from a non-zero parameter value and then realizes a falling ramp of that parameter, there is a mandatory, unde...
9 replies
F
Bandwidth of SUServo
- Asking for helpARTIQSinara
- We are testing the SUServo, with a specific frequency noise mix with AOM RF(Urukul output) to disturb the light and using a PD to capture the optical power as the input of Sam...
3 replies
F
Create a description file of SUServo
- Asking for helpARTIQSinara
- Hello, I am trying to exploit our ARTIQ SUServo feature to stablize our laser. However, our hardware was not set to SUServo mode when it had been ordered. Now, I know that the...
3 replies
V
artiq.db failed to download in MSYS2
- Asking for helpARTIQ
- Hello, we have installed MSYS2 using the offline installer provided in the ARTIQ manual. On Windows 10. The problems we have: Any command of the sort ''pacman -S ...'' returns...
3 replies
D
ARTIQ 9 with NAC3 not providing error messages
- Asking for helpARTIQSinara
- I've flashed a crate with gateware built from the NAC3 branch of ARTIQ, and I have a nix environment with the same git version for running the master/dashboard/moninj/coreanal...
3 replies
D
ARTIQ9/NAC3 gateware issue
- Asking for helpARTIQSinara
- I'm trying to test out ARTIQ9 with NAC3 on a spare Kasli crate we have, and I have the master/dashboard/moninj working and talking to the crate. I haven't been able to run any...
2 replies
A
Reading values of the ADC input
- Asking for helpARTIQ
- Hi, when I'm trying to read an input voltage from an oscilloscope with an ADC channel it gives the following error: <artiq>/coredevice/sampler.py:149:13-149:16: error: the arg...
1 reply
F
Problem encountered in setup nix develop environment
- Asking for helpARTIQSinara
- When we was running the followed code in my ubuntu system: nix develop git+https://git.m-labs.hk/m-labs/artiq-zynq\?ref=release-8 We met a problem in install phase: error: bui...
3 replies
A
Bash scripting to for MSYS2 with ARTIQ?
- Asking for help
- In the past, we have used bash scripts to navigate to our artiq folder and then run the necessary start up commands: artiq_master, artiq_cltmgr, and artq_dashboard. This was w...
5 replies
F
Difference of file size of the binary gateware and firmware
- Asking for helpARTIQSinara
- I currently setup a DRTIO system which contain two artiq machine, driven by different core --- Kasli and Kasli-SoC After I tried to build firmware and gateware for the Kasli a...
3 replies
A
Flashing Shuttler
- Asking for helpARTIQ
- Hi all, We have a shuttler which we want to get up and running. As part of flashing the EFC (EEM FMC Carrier), we'd like to see the logs through the UART port. My understandin...
7 replies
P
Underflow Errors on Long (but slowish) Scans
- Asking for help
- Hi All, I am trying to document and understand the behavior of the sampler and the zotino dac functions. The idea here is to be able to take data for long periods of time with...
1 reply
D
Bug in Urukul DRG: output depends on power cycling Kasli (SoC)
- Asking for helpARTIQSinara
- Again a bug that I managed to isolate well: I took the experiment from Bug in Urukul DRG: output amplitude is initialized to lower limit and added these lines just before the ...
1 reply
K
Cannot Ping 192.168.1.75 and SFP Port Light Not Illuminating
- Asking for help
- I am currently facing an issue with my ARTIQ device and would greatly appreciate any assistance from the community. I am unable to ping the device's IP address, and the SFP po...
6 replies
D
Bug in Urukul DRG: output amplitude is initialized to lower limit
- Asking for helpARTIQSinara
- I have isolated this bug extremely well. The self-contained experiment below writes an activated amplitude DRG into CFR2, sets DRCTL=high, waits 5 microseconds, then pulses io...
3 replies
H
Trouble installing second dds (urukul ad9910)
- Asking for helpARTIQSinara
- Hello, I have been recently attempting to install a second dds (Creotech Urukul ad9910) into my labs Artiq system. Previous to the 2nd instillation there was already a functio...
14 replies
D
Bug in new Urukul features
- Asking for helpARTIQSinara
- UPDATE: I leave this post here so it can be looked up, but I isolated constituent bugs better in these posts: https://forum.m-labs.hk/d/960-bug-in-urukul-drg-output-amplitude-...
0 replies
D
`proto_rev` in system description file required to use new Urukul features?
- Asking for helpARTIQSinara
- I tried to use the new Urukul features, but now a simple experiment that switches on a single DDS channel for 5 microseconds outputs a much much smaller voltage amplitude than...
3 replies
J
Urukul Nominal Output Power Incorrect
- Asking for helpSinara
- I am unsure of how to troubleshoot our Urukul outputting the incorrect nominal dBm. For reference, we are running Urukuls at 80 MHz with 0 digital attenuation. We have two sep...
1 reply
D
"can't modify CPUCS: Broken pipe" on Digilent's JTAG-HS2 cable
- Asking for helpSinara
- On Ubuntu Server 22.04 LTS (no GUI), I installed Xilinx ISE 14.7 including cable drivers, but the cable driver installation failed with: Installing hotplug script..... error: ...
7 replies

AD9910: Mirror frequencies invert sign of phase accumulation

Bandwidth of SUServo

Create a description file of SUServo

artiq.db failed to download in MSYS2

ARTIQ 9 with NAC3 not providing error messages

ARTIQ9/NAC3 gateware issue

Reading values of the ADC input

Problem encountered in setup nix develop environment

Bash scripting to for MSYS2 with ARTIQ?

Difference of file size of the binary gateware and firmware

Flashing Shuttler

Underflow Errors on Long (but slowish) Scans

Bug in Urukul DRG: output depends on power cycling Kasli (SoC)

Cannot Ping 192.168.1.75 and SFP Port Light Not Illuminating

Bug in Urukul DRG: output amplitude is initialized to lower limit

Trouble installing second dds (urukul ad9910)

Bug in new Urukul features

`proto_rev` in system description file required to use new Urukul features?

Urukul Nominal Output Power Incorrect

"can't modify CPUCS: Broken pipe" on Digilent's JTAG-HS2 cable